Makita UC3530A Manual de instrucciones Pagina 23
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
23
Trouble shooting
Malfunction System Observation Cause
Chain saw does not work total electric motor does not
function
no power supply,
cable defective
chain brake actuated
Mains fuse blown
insufficient performance Carbon brushes low pulling power Carbon brushes worn
down
no chain lubrication Oil tank, oil pump no oil on the saw chain oil tank empty,
oil guide groove dirty
Chain brake Brake Saw chain does not stop
instantly
Brake band worn down
Run-out brake Brake Saw chain continues to run Carbon brushes worn
down
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance
must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly.
Failure to perform the prescribed maintenance work can lead to accidents!
The user of the electric chain saw is not allowed to perform maintenance works which are not described in the
instruction manual. All other works must be carried out by a MAKITA service centre.
General work Electric chain saw Regularly clean the outside.
Plastic case Check for cracks and ruptures. In case of damage have it
immediately repaired at a service centre.
Saw chain Resharpen regularly.
Replace in time.
Guide bar Turn over after a certain period of time so that the bearing
surfaces are uniformly worn.
Replace in time.
Sprocket Have it replaced in time at a service centre.
Chain brake Have it inspected regularly at a service centre.
Run-out brake Have it inspected regularly at a service centre.
Each time before putting
the saw into operation
Saw chain Check for damage and sharpness.
Check the chain tension.
Guide bar Check for damage, and remove burrs if necessary.
Chain lubrication Functional check.
Chain brake Functional check.
Run-out brake Functional check.
Power switch Functional check.
Power supply cable In case of damage have it replaced at a service centre.
Oil tank cap Check for tightness.
After each shutdown Guide bar Clean the oil inlet bore.
Chain carrier Clean, especially the oil guide groove.
Storage Chain oil tank Empty.
Saw chain/guide bar Demount, clean and lubricate slightly.
Clean the guide groove of the guide bar.
Electric chain saw Store safely in a dry place. After a long storage time, have
the electric chain saw checked at a service centre (residual
oil can become resinic and the valve of the oil pump
clogged).
- Waste oil 7
- Intended use 12
- Minimum delivery inventory 12
- EC Declaration of Conformity 12
- Safety precautions 13
- Putting into operation 14
- Kickback 15
- Transport and storage 16
- First aid (Fig. 24) 16
- WARNING: 17
- 1 Tubular handle 18
- MAINTENANCE 21
- (Fig. 61) 22
- Trouble shooting 23
- Maintenance and repair 24
- Spare parts 24
- Заходи безпеки 27
- Введення в експлуатацію 28
- Транспортування та зберігання 30
- Перша допомога (Мал. 24) 31
- ПРИМІТКА: 31
- 1 Трубчаста ручка 33
- ОБСЛУГОВУВАННЯ 36
- (Мал. 58) 37
- Заміна ланцюга пили (Мал. 59) 37
- Усунення несправностей 38
- Обслуговування та ремонт 39
- Запасні частини 39
- Przeznaczenie 41
- Minimalny zakres dostawy 41
- Deklaracja zgodności UE 41
- Zasady bezpieczeństwa 42
- Sprzęt ochrony osobistej 43
- Uruchomienie 43
- Przewożenie i przechowywanie 45
- Pierwsza pomoc (Rys.24) 46
- OSTRZEŻENIE: 47
- URUCHOMIENIE (Rys. 25) 49
- KONSERWACJA 51
- Rozwiązywanie problemów 53
- Konserwacja i naprawy 54
- Części zapasowe 54
- Scopul utilizării 56
- Inventar minim de livrare 56
- Declaraţie de conformitate CE 56
- Măsuri de siguranţă 57
- Punere în funcţiune 58
- Transport şi depozitare 60
- Primul ajutor (Fig. 24) 60
- AVERTISMENT: 62
- 1 Mâner tubular 63
- ÎNTREŢINERE 66
- Depanare 68
- Întreţinere şi reparaţii 69
- Piese de schimb 69
- Verwendungszweck 71
- Mindestlieferumfang 71
- EG-Konformitätserklärung 71
- Arbeitsschutz 72
- Persönliche Schutzausrüstung 73
- Inbetriebnahme 73
- Arbeiten 74
- Rückschlag 75
- Transport und Lagerung 75
- Erste Hilfe (Abb. 24) 76
- HINWEIS: 76
- WARNUNG: 77
- 1 Bügelgriff 78
- INBETRIEBNAHME (Abb. 25) 79
- Problembehebung 83
- Wartung und Reparatur 84
- Ersatzteile 84
- Rendeltetés 86
- Minimális rakjegyzék 86
- EK Megfelelőségi nyilatkozat 86
- Biztonsági óvintézkedések 87
- Üzembe helyezés 88
- Bánásmód és munkamódszer 89
- Visszarúgás 90
- Szállítás és tárolás 90
- Elsősegély (24. ábra) 90
- MEGJEGYZÉS 90
- FIGYELEM: 92
- 1 Kengyelfogantyú 93
- ÜZEMBEHELYEZÉS (25. ábra) 94
- KARBANTARTÁS 96
- (58. ábra) 97
- Hibakeresés 98
- Karbantartás és javítások 99
- Pótalkatrészek 99
- ..... mm 100
- Určené použitie 101
- Minimálny rozsah dodávky 101
- Európskeho spoločenstva 101
- Bezpečnostné opatrenia 102
- Uvedenie do prevádzky 103
- Spätný náraz 105
- Prevoz a skladovanie 105
- Prvá pomoc (Obr. 24) 105
- POZNÁMKA 106
- VÝSTRAHA: 107
- 1 Rúrková rukoväť 108
- Pilníky a ako s nimi pracovať 112
- Riešenie problémov 113
- Pokyny na pravidelnú údržbu 113
- Údržba a opravy 114
- Náhradné diely 114
- Účel použití 116
- Minimální obsah dodávky 116
- Prohlášení ES o shodě 116
- Bezpečnostní opatření 117
- Uvedení do provozu 118
- Zpětný vrh 119
- Přeprava a skladování 120
- První pomoc (Obr. 24) 120
- VAROVÁNÍ: 121
- 1 Obloukové držadlo 122
- UVEDENÍ DO PROVOZU (Obr. 25) 123
- Odstraňování problémů 127
- Pokyny pro pravidelnou údržbu 127
- Makita Corporation 128
- Anjo, Aichi, Japan 128
- 884666D204 128
Relacionado con productos y manuales para Motosierras Eléctricas Makita UC3530A
(32 paginas)
(5 paginas)
(10 paginas)
(1 paginas)
(60 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales