Makita 2703X1 Manual de usuario

With Electric Brake210 mm (8-1/4”)MODEL 2702X1MODEL 2702255 mm (10”)MODEL 2703X1MODEL 2703Table Sawwww.makita.comINSTRUCTION MANUALDOUBLEINSULATIONWAR

10Adjusting depth of cutThe depth of cut may be adjusted by turning the han-dle. Turn the handle clockwise to raise the blade orcounterclockwise to lo

After adjusting the positive stops, set the blade at 90° tothe table surface. Then adjust the arrow pointer so thatits right edge is aligned to the 0

12CAUTION:• Always grasp the striped portion of the wrench whentightening the hex bolts. If you tighten the hex boltswhile grasping the wrench further

When operating the switch lever, it is convenient toview it through the window area in the table.CAUTION:• When not using the tool, remove the key and

14Push stickA push stick can be easily made from a piece of ply-wood 19 mm (3/4”) to 25 mm (1”) thick. Cut out the hatched area on the stick and smoot

Wood facing (rip fence)A wood facing should be used for operations when theblade comes close to the rip fence. Wood facing for the ripfence should be

16Auxiliary wood facing (miter gauge)To prevent a long board from wobbling, fit the mitergauge with an auxiliary fence board. Fasten withbolts/nuts af

3. Turn the tool on and gently feed the workpiece intothe blade along with the rip fence. (1) When the width of rip is 150 mm (6”) and wider,carefully

CAUTION:• Always be sure that the tool is switched off andunplugged before attempting to perform inspection ormaintenance.CleaningClean out sawdust an

19CAUTION:• These accessories or attachments are recommendedfor use with your Makita tool specified in this manual.The use of any other accessories or

2MODELArborholeBladediameterCutting capacities90° 45°Table size(W x L)No load speed(RPM)Dimensions(L x W x H)Maximum dado capacityNetweight18kg(40 lbs

Table insert(Part No. 317061-6)When cutting grooves 5/16”, 3/8”,7/16” or 1/2” use thistable insert instead of the standard table insert. To install th

21NOTE:• When widths slightly greater than the above arerequired, fit the paper washers in between the insideand outside cutters to adjust the width.

Featherboards are used to keep the workpiece in con-tact with the rip fence and table as shown, and to stopkickbacks.To install featherboards, proceed

23How to perform rabbeting1. Remove blade guard.2. Attach auxiliary fence to rip fence for cuts that run thelength of the stock. Facing should be as h

24CAUTION:• These accessories or attachments are recommendedfor use with your Makita tool specified in this manual.The use of any other accessories or

21First-ClassPostageRequiredPost Office willnot deliverwithout properpostage.Makita U.S.A., Inc.14930 Northam StreetLa Mirada, CA 90638-5753FoldCut

221. This product was purchased from:Home CenterHardware/Lumber StoreTool DistributorIndustrial SupplyConstruction SupplyOther ( )

27FACTORY SERVICE CENTERS1-800-4-MAKITARETAIN THIS PORTION FOR YOUR RECORDSALABAMA2365 Pelham ParkwayPelham, AL 35124 (205) 620-1791ARIZONA3707 E. Bro

WARNINGSome dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to the State of Calif

39. USE RIGHT TOOL.Don’t force tool or attachment to do a jobfor which it was not designed; for example,don’t use circular saw for cutting tree limbso

416. REDUCE THE RISK OF UNINTENTIONAL STARTING.Make sure switch is in off position beforeplugging in.17. USE RECOMMENDED ACCES-SORIES.Consult the owne

51. Wear eye protection.2. Don’t use the tool in presence of flam-mable liquids or gases.3. NEVER use the tool with an abrasive cut-off wheel installe

618. Do not perform any operation freehand.Freehand means using your hands to sup-port or guide the workpiece, in lieu of a ripfence or miter gauge.19

The tool is shipped from the factory with the saw bladeand blade guard not in the installed condition. Assembleas follows:CAUTION:• Always unplug the

8Installing blade guardCAUTION:• Before installing the blade guard, adjust the depth ofcut to its maximum elevation. Insert the spreaderbetween the bl

9Positioning table sawLocate the table saw in a well lit and level area whereyou can maintain good footing and balance. It shouldbe installed in an ar