Makita BTS130 Especificaciones

PRODUCT NAMEHitachi 14.4 V Cordless Oil Pulse DriverModel WP 14DSL• Tightening and loosening of small screws, tapping screws, wood screws, Teks scre

-7-2. Screwing Time and Capacity (Number of Screws Tightened)(1) Screwing timeThe table below compares the screwing time for the Hitachi pulse driver

-8-1. Safety InstructionsIn the interest of promoting the safest and most efficient use of the Model WP 14DSL Cordless Oil PulseDriver by all our cust

-9-WARNING • To reduce the risk of injury, user must read and understand Instruction Manual.AVERTISSEMENT • Afin de réduire le risque de blessures,

-10-CAUTION• Read thoroughly HANDLING INSTRUCTIONS before use.• Do not disassemble nor throw into fire. • For safe operation, see instruc

-11-3. About Reduction in Tighten Torque(1) Battery voltage ------------------------------ The tightening torque of the Pulse Driver is affected by ba

-12-Small flat-blade screwdriverPulse Unit [13]Retaining Ring [1]Retainer [2]Retaining Ring [1]OpeningGuide Sleeve (A) [4]WARNING: Always remove the b

-13-2. Front Cap, Front CoverInsert the small flat-blade screwdriver between the Front Cap [5] and Front Cover [6], and then removeboth from Hammer Ca

-14-Inner Cover (D) [25]Ring Gear (E) [21]BALL BEARING6901VV-N [23]Damper [24]Washer (E) [22]Armature DC 14.4V [26]Damper [24]Inner Cover (D) [25]BInn

-15-Lead wire (black)Lead wire (brown)Controller [46] (front)Terminal supportTerminal support LD terminalLead wire (white)Lead wire (brown)Lead wire (

-16-Thread the lead wire through thespace between ribs of the housingLead wire (black)Lead wire (red) Fig. 5 • Switch-related reassembly (3)(2) Conn

REMARKS:• For more information about HANDLING INSTRUCTIONS, visit our website at:http://www.hitachi-koki.com/manual_view_export/• This TECHNICAL DATA

-17-Set the Impact Change lever ofHousing (A) to the "P" position forreassembly.Controller [46]Terminal supportThread brown lead wire into s

-18-Side Yoke [50]Magnet (D) [27]Yoke (A) [28]Dust GuardFin (C) [29]Depressed partBrush Block [30]Projected partDust Guard Fin (C) [29]FlangeProjected

-19-Inner cover ribHammer case ribHammer Case [7] end surface(3) Connecting hammer case assembly and armature assemblyMount the Washer [16] on the Gea

-20-Hammer Case [7] must be firmly fitted to the housing.Hammer Case [7]Mount the LED light on thisportion of Hammer Case [7].Thread the LED lead wire

-21-The blade portion of Dust Guard Fin (C) [29]must come under the rib of Housing (A).Packing [44]Strap (Black) [48] insertion bossLock Nut M4(Black)

-22-J-295 jig (A)for retaining ringRetaining Ring [1]Retainer [2]J-295 jig (B)for retaining ringPush down. Fig. 15 • Mounting Guide Sleeve (A)4. Rea

-23-(1) ATTOLUB MS No. 2• Armature DC 14.4V [26] pinion gear face, Ring Gear (E) [21] face, and gears of the two Idle GearSets [17]• Two Steel Balls D

-24-MODEL VariableFixed10 20 30 40 50 60 min.Work FlowWP 14DSLGeneral assemblyHookGuide Sleeve (A)Switch Ass'yInner Cover (D)ArmatureDC 14.4VMa

Model WP 14DSLLIST NO. H8462010 10 6(E2)CORDLESS OIL PULSE DRIVER1234562078910131214151617181921222324252627282930323133343935363738404348444145424146

PARTSWP 14DSL DESCRIPTION REMARKS1 995-933 RETAINING RING 12 307-899 RETAINER 13 995-931 GUIDE SPRING 14 307-782 GUIDE SLEEVE (A) 15 322-239 FRO

CONTENTSPageSELLING POINTS -------------------------------------------------------------------------------------------------------------- 1SPECIFICATI

WP 14DSL DESCRIPTION REMARKS501 CHARGER (MODEL UC18YRSL) 1502 983-006 + DRIVER BIT NO.2 65L 1503 329-897 BATTERY COVER 1504 329-440 CASE ASS&apo

WP 14DSL DESCRIPTION REMARKS- 4 - Printed in Japan 10 - 10 (101006N) *ALTERNATIVE PARTSNO.USEDC

-1-Full lengthLightweight and compact*The Hitachi Cordless Oil Pulse Driver (Model WP 14DSL) is superior to the competitive product ofCompany M in bot

-2-BladeLiner caseLinerOilMain shaftTorque-generating seal portionTorque-generating sealportionLiner caseMain shaftOilBefore torquegenerationThere is

-3-SwitchableScrewing in Save mode (16 N•m)*• Best suitable for light load worksUse to tighten wood screws of smalldiameters or to adjust screwing!Scr

-4-1. SpecificationsModelItemWP 14DSLCapacityMachine screw*1: 4 to 8 mmWood screw: 3.5 mm to 9.5 mmTightening torque 30 N•m (306 kgf•cm 266 in-lbs.)Ti

-5-2. Optional Accessories(1) Plus driver bitBit No. Code No.No. 2 992671No. 3 992672(2) Hexagon socketPart name Stamped figures Code No. L (mm) B (mm

-6-1. Comparison of Specifications (Superior specifications: )HITACHIMakerModelItemWP 14DSL(LSRK)WP 12DM(RCK)WH 14DSL(2SLCK)MMachine screwmm4